Palo Alto Networks Enterprise Firewall PA-3260
Next-Generation Firewall Appliance in a Ruggedized Form Factor

Palo Alto Networks Enterprise Firewall PA-3260

Palo Alto Networks Products

PA-3260 Series Hardware

Palo Alto Networks PA-3260

#PAN-PA-3260
המחיר שלנו: הצעת מחיר

מחירים נוספים מופיעים למטה, או לחצו כאן!

שימו לב: כל המחירים באתר כוללים מע"מ. החיוב יבוצע על פי שער "העברות והמחאות מכירה" של המטבע (דולר אמריקאי) ביום אישור ההזמנה.

סקירה:

The Palo Alto Networks® PA-3200 Series next-generation firewalls are designed for data center and internet gateway deployments. This series is comprised of the PA-3260, PA-3260, and PA-3260 firewalls. These models provide flexibility in performance and redundancy to help you meet your deployment requirements. All models in this series provide next-generation security features to help you secure your organization through advanced visibility and control of applications, users, and content.

First Supported Software Release: PAN-OS® 8.1

מאפייני המערכת:

8.8 Gbps firewall throughput¹
(App-ID enabled¹)
4.7 Gbps Threat Prevention throughput²
4.8 Gbps IPsec VPN throughput
3,000,000 max sessions
135,000 new sessions per second³
6,000 IPsec VPN tunnels/tunnel interfaces
2,048 SSL VPN Users
10 virtual routers
1/6 virtual systems (base/max⁴)
60 security zones
5,000 max number of policies

Front Panel:

Item	Component	Description
1	Ethernet ports 1 through 12	Twelve RJ-45 10Mbps/100Mpbs/1Gbps ports for network traffic. The link speed and link duplex are auto-negotiate only.
2	SFP ports 13 through 20	These ports vary depending on your firewall model: PA-3260 firewall—Ports 13 through 16 are SFP (1Gbps) and ports 17 through 20 are SFP or SFP+ (10Gbps) based on the installed transceiver. PA-3260 and PA-3260 firewalls—Ports 13 through 20 are SFP (1Gbps) or SFP+ (10Gbps) based on the installed transceiver.
3	QSFP+ ports 21 through 24	(`PA-3260 only`) Four QSFP+ (40Gbps) ports as defined by the IEEE 802.3ba standard.
4	HSCI port	One SFP+ (10Gbps) port (supports only an SFP+ transceiver or passive SFP+ cable). Use this port to connect two PA-3200 Series firewalls in a high availability (HA) configuration as follows: In an active/passive configuration, this port is for HA2 (data link). In an active/active configuration, you can configure this port for HA2 and HA3. HA3 is used for packet forwarding for asymmetrically routed sessions that require Layer 7 inspection for App-ID and Content-ID. The HSCI ports must be connected directly between the two firewalls in the HA configuration (without a switch or router between them). When directly connecting the HSCI ports between two PA-3200 Series firewalls that are physically located near each other, Palo Alto Networks recommends that you use a passive SFP+ cable. For installations where the two firewalls are not near each other and you cannot use a passive SFP+ cable, use a standard SFP+ transceiver and the appropriate cable length.
5	HA1-A and HA1-B ports	Two RJ-45 10Mbps/100Mbps/1000Mbps ports for high availability (HA) control. If the firewall dataplane restarts due to a failure or manual restart, the HA1-B link will also restart. If the dataplane restarts and only HA1-B is connected, a split brain condition occurs. The HA1-A link will not restart when the dataplane restarts. Because of this behavior, we recommend that you connect both HA1-A and HA1-B to provide redundancy for the control link and to avoid split brain issues.
6	MGT port	Use this Ethernet 10Mbps/100Mbps/1000Mbps port to access the management web interface and perform administrative tasks. The firewall also uses this port for management services, such as retrieving licenses and updating threat and application signatures.
7	CONSOLE port (RJ-45)	Use this port to connect a management computer to the firewall using a 9-pin serial-to-RJ-45 cable and terminal emulation software. The console connection provides access to firewall boot messages, the Maintenance Recovery Tool (MRT), and the command line interface (CLI). If your management computer does not have a serial port, use a USB-to-serial converter. Use the following settings to configure your terminal emulation software to connect to the console port: Data rate: 9600 Data bits: 8 Parity: None Stop bits: 1 Flow control: None
8	USB port	A USB port that accepts a USB flash drive with a bootstrap bundle (PAN-OS configuration). Bootstrapping speeds up the process of configuring and licensing the firewall to make it operational on the network with or without internet access.
9	CONSOLE port (Micro USB)	Use this port to connect a management computer to the firewall using a standard Type-A USB-to-micro USB cable. The console connection provides access to firewall boot messages, the Maintenance Recovery Tool (MRT), and the command line interface (CLI). Refer to the Micro USB Console Port page for more information and to download the Windows driver or to learn how to connect from a Mac or Linux computer.
10	LED status indicators	Eight LEDs that indicate the status of the firewall hardware components (see Interpret the PA-3200 Series Status LEDs ).

Back Panel:

Item	Component	Description
1	System drive	One 240GB solid-state drive (SSD) used to store the PAN-OS system files, system logs, and network traffic logs.
2	Exhaust fan tray	Provides ventilation and cooling for the firewall.
3	Ground studs	Use the two-post ground stud to connect the firewall to earth ground. The firewall ships with a 6AWG two-post ground lug (attached to the ground studs) but does not include a ground cable.
4	PS1 and PS2 power supplies	Use the power supply inputs (either AC or DC depending on the installed power supply type) to connect power to the firewall. The second power supply is for redundancy. When facing the back of the firewall, PS1 is on the left and PS2 is on the right.

הורדת מפרט טכני:

Download the Palo Alto Networks PA-3260 Specification Datasheet (PDF).

הערות תמחור:

מחירי המוצרים וזמינותם כפופים לשינויים ללא הודעה מוקדמת.

Palo Alto PA-3260 Series Hardware Series